CDMO

Botanical Extract Standardization: Marker Compounds, Ratios and COA Traps

“Standardized to 80% silymarin” is a sentence that means almost nothing on its own. Eighty percent measured by UV absorbance and eighty percent measured by HPLC against a specific standard are different products at different prices, and both certificates will print the same number.

Marker versus ratio extracts

A ratio extract (4:1, 10:1) describes how much raw herb went in, not what came out. It is a manufacturing statement, not a potency claim, and two 10:1 extracts can differ by a factor of three in active content. A standardized extract names a marker compound and a method; that is the only version worth writing into a purchase specification.

For Silymarin, UV methods overstate content because they read total flavonolignans including inactive ones. An HPLC specification against silybin A and B is tighter and more expensive. Decide which one your label claim actually needs before comparing quotes.

The carrier dilutes everything, including your claim

Extracts are frequently standardized onto a carrier — maltodextrin, dextrose, silicon dioxide — and the carrier percentage is rarely volunteered. A 50% silymarin extract on a maltodextrin carrier and a 50% extract without carrier are not interchangeable at the same dose, and the difference shows up in the finished capsule weight. Ask for the carrier identity, the carrier percentage, and the assay on the extract itself rather than on the blended powder.

Contaminants that a potency COA will not mention

  • Pesticide residues — the single most common failure for leafy and root botanicals. Demand a multi-residue panel to the destination market's limits.
  • PAH and solvent residues — relevant where extraction uses acetone, ethanol or hexane; specify the residual solvent class.
  • Heavy metals — lead and cadmium concentrate in root and bark materials and vary by harvest region.
  • Ethylene oxide and irradiation — a microbial control method that some markets prohibit; get a written statement, not an assumption.

Product-specific checks

Green Tea Extract is bought on EGCG content, but the same specification can hide very different caffeine levels — decaffeinated grades cost more and must be specified explicitly. Ginkgo Biloba Extract is conventionally standardized to 24% flavonol glycosides and 6% terpene lactones, and the ginkgolic acid limit is the line that decides whether the lot is acceptable in the EU.

Astragalus Extract and Echinacea Extract are usually bought on polysaccharide or marker content where the analytical method varies widely between laboratories. Mushroom Extract quality turns on beta-glucan content and on whether the material is mycelium-on-grain or fruiting body — two very different products under one name. Phytosterol is specified on total sterol content and the beta-sitosterol share, and Spirulina on phycocyanin plus microbial limits.

What to write into the purchase specification

ProductLines that matter
SilymarinMarker and method (HPLC vs UV); carrier; heavy metals; pesticide panel
Green tea extractEGCG %; total catechins; caffeine %; residual solvent
Ginkgo extract24% flavonol glycosides; 6% terpene lactones; ginkgolic acid
Mushroom extractBeta-glucan %; fruiting body vs mycelium; carrier

Sourcing note

Botanical extracts are quoted with the analytical method stated on the COA rather than a bare percentage, and 25 kg MOQ applies to most grades. Where a customer's label claim depends on a specific marker method, we will quote against that method and supply the chromatogram with the lot.

Running a trial that predicts the line

Send the marker method with the enquiry. A supplier who can quote against your HPLC method and return a chromatogram is a different class of supplier from one who can only restate a percentage. Request two consecutive lots and compare the chromatograms — lot-to-lot consistency is what a standardized extract is supposed to deliver, and a single sample cannot demonstrate it.

For capsule or tablet applications, also ask for the bulk density and the flow of the blended powder. A 50% extract on a maltodextrin carrier flows differently from the same marker content without carrier, and the difference shows up as weight variation on the encapsulator, not in the assay.

X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept